strain gauge transmitters
Strain gauge amplifier HART

Strain gauge amplifier HART

type: DRMU-S2 - DRSG-S2  | ID: DR series 2

technical features

  • Input: 1 strain gauge full bridge
  • Bridge resistance: 350 Ω minimum
  • Output: 4...20 mA HART current loop
  • Supply: Current loop
  • Electrical connection: 2...6 plug-in terminal strip
  • Limit vale contacts: without
  • Protection: IP20
  • Accuracy: see data sheet
  • Enclosure: for DIN rail

Strain gauge amplifier HART

Strain gauge amplifier HART

type: DRMU-S4 - DRSG-S4 | ID: DR series 4

technical features

  • Input: 1 strain gauge full bridge
  • Bridge resistance: 350 ohms minimun
  • Output: 4...20 mA HART current loop
  • Supply: 24 VDC, 85...250 VAC, current loop
  • Electrical connection: 2...6 plug-in terminal strip
  • Limit vale contacts: 2x electronically,
    2x relays
  • Protection: IP20
  • Accuracy: see data sheet
  • Enclosure: for DIN rail

Digital measuring amplifier for strain gauge HART

Digital measuring amplifier for strain gauge HART

type: ADHM-LC | ID: LH

technical features

  • Connection: 1x strain gauge full bridge, 350 ohms
  • Input sensitivity: 1...4 mV/V
  • Configuration: via HART interface
  • Output: 4...20 mA HART
  • Supply: 12...40 VDC out of current loop
  • Electrical connection: pluggable - Combined error: 0,3% of nominal range
  • Resolution: 16 bit
  • Enclosure: stainless steel
  • Protection: IP 65

DMS - Brücken - Messverstärker SIL3 + PL"e"

Strain Gauge Bridge Amplifier SIL3 + PL"e"

type: SMM-DR | ID: ▒

technical features

  • Sensor input: 1x strain gauge full bridge (350 ohms)
  • Stain gauge sensitivity: up to 4 mV/V
  • Bridge supply: 5 VDC
  • Analog output: 2x 4...20 mA
  • Voltage supply: 24 VDC +/-10%
  • Accuracy: 5% deviation channel A / channel B
  • Protection: IP20
  • Diagnostic input: Test pulse 24 VDC
  • Enclosure: DR22,5 (117,2x22,5x113,6)
  • Certificate: SIL 3, Performance Level "e"

Digital strain gauge amplifier

Strain Gauge Bridge Amplifier SIL3 + PL"e"

type: SMM-HD | ID: ▒

technical features

  • Sensor input: 1x or 2x strain gauge full bridge (350 ohms)
  • Stain gauge sensitivity: up to 4 mV/V
  • Bridge supply: 5 VDC
  • Analog output: 2x 4...20 mA for each strain gauge
  • Voltage supply: 24 VDC +/-10%
  • Accuracy: 5% deviation channel A / channel B
  • Protection: IP20
  • Diagnostic input: Test pulse 24 VDC
  • Enclosure: U-CASE2 (162,2 x 92,2 (101,1) x 60,2 mm)
  • Certificate: SIL 3, Performance Level "e"

Digital strain gauge amplifier

Digital strain gauge amplifier

type: ADLM-HD | ID: DD

technical features

  • Input: up to 4 strain gauge full bridges
  • Input sensitivity: 0,1...5 mV/V
  • Analog output: 4...20 mA / 0...10 V
  • Voltage supply: 24 VDC +/-30%
  • Resolution: 12 / 14 / 15 / 16 bit
  • Combined error: 0,2% of end scale value
  • Optionally: limit value switch / interface / vibration protection
  • Degree of protection: IP65
  • Adjustment: via RS232 interface

Digital strain gauge and standard signal amplifier

Digital strain gauge and standard signal amplifier

type: ADLM-NS | ID: AD

technical features

  • Input Strain gauge: up to 4 full bridges
  • Input sensitivity: 0,1...5 mV/V
  • Input standard signal: 4...20 mA, 0...10 V
  • Analog output: 4...20 mA / 0...10 V
  • Voltage supply: 24 VDC
  • Resolution: 12 / 14 / 15 / 16 bit
  • Combined error: 0,2% of end scale value
  • Optionally: limit value switch / interface
  • Degree of protection: IP20
  • Adjustment: via RS232 interface

Digital strain gauge amplifier

Digital strain gauge amplifier

type: DR-ADLM | ID: BD

technical features

  • Input Strain gauge: up to 2 full bridges, 0(4)...20 mA, 0...10 V
  • Input sensitivity: 0,1...5 mV/V
  • Analog output: 4...20 mA / 0...10 V
  • Voltage supply: 24 VDC
  • Resolution: 12 / 14 / 15 / 16 bit
  • Combined error: 0,2% of end scale value
  • Optionally: interface
  • Degree of protection: IP20
  • Adjustment: via RS232 or USB interface

Strain gauge amplifier HART

Strain gauge amplifier HART

type: MISG | ID: MJ

technical features

  • Input strain gauge: 1 full bridge, 4-wire
  • Input sensitivity: 1...4 mV/V
  • Output: 4...20 mA HART
  • Voltage supply: 12...40 VDC
  • Resolution: 16 bit
  • Combined error: 0,3% of range
  • Bridge supply: 1 VDC
  • Protection: at least IP65
  • Configuration: Software with HART communication

Mobile digital strain gauge amplifier

Mobile digital strain gauge amplifier

type: ADLM-HA | ID: DM

technical features

  • Input: 2 strain gauge full bridges
  • Input sensitivity: 0,1...5 mV/V
  • Analog output: 4...20 mA / 0...10 V
  • Voltage supply: accumulator
  • Resolution: 12 / 14 / 15 / 16 bit
  • Combined error: 0,2% of end scale value
  • Degree of protection: IP54
  • Adjustment: via RS232 interface or programming keys

Digital load measuring system

Digital load measuring system

type: DLMHD | ID: LS

technical features

  • TÜV approval for use in systems with AK4
  • µP-device for simple programming
  • 4 resistance strain gauge full-bridge sensors
  • 2 adjustable limit switches, relay output with restraint
  • Configurable analog output, 0...1(10)v or 0(4)...20mA galvanic insulation
  • Interfaces RS232, RS485, Interbus S, LWL, CANbus, Profibus galvanically insulated
  • Tare - function
  • Redundant construction for limit switch and test equipment, monitoring of sensor break and short circuit
  • Accuracy +/- 0,1% of end scale value

Digital measuring amplifier for strain gauge

Digital measuring amplifier for strain gauge

type: SU-DX | ID: DL

technical features

  • Input sensivity 01 to 5 mV/V
  • Programmable via RS232 interface
  • Analog output 4...20 mA and 0...10 V
  • Supply voltage 24 VDC +/- 30%
  • Combined error 0,2% FS
  • Resolution 12 / 14 / 15 / 16 bit
  • Enclosure plastics
  • Degree of protection IP 67

Sixfold strain gauge summing-up box

Sixfold strain gauge summing-up box

type: DSV-6N | ID: SD

technical features

  • Input: 6 strain gauge full bridges
  • Output: 1 strain gauge summing-up signal
  • Sensors: 4- or 6-wires
  • Bridge supply: out of amplifier or internally
  • Supply: 12...30 VDC VDC (optionally)
  • Cascade circuit possible
  • Connection: screwed pin and socket, lockable
  • Cable entries: 7 pcs M16x1,5

Measuring amplifier strain gauge

Measuring amplifier strain gauge

type: ALM-HD2 | ID: AJ

technical features

  • Input sensitivity (0,1 mV/V up to 4 mV/V) selectable by DIP-switches
  • Connection of max. 4 resistance strain gauge sensors (full bridge, 350 ohms)
  • Change over analog output 0 (4)...+/- 20 mA or 0 (2)...+/-10 V
  • Sensor supply voltage internally continiously adjustable (4...14 V)
  • Optionally 2 adjustable limit value switches (potential free change over contacts)
  • Accuracy +/-0,1% of end of scale value
  • Supply voltage 85...265 VAC or 24 VDC

Analog Strain Gauge Amplifier

Analog Strain Gauge Amplifier

type: ALM-NS | ID: AN

technical features

  • Input strain gauge: up to 4 full bridges (350 Ω)
  • Sensitivity strain gauge: 0,1...4 mV/V (by steps)
  • Output: 2...10 V and 4...20 mA, 0...10 V and 0...20 mA
  • Voltage supply: 42 VAC / 115 VAC / 230 VAC / 24 VAC24 VDC
    galvanically isolated
  • Limit value: 2 floating contacts (option)
  • Bridge supply: 4...14 V adjustable
  • Linearity: ± 0,02% of terminal value
  • Mounting: top hat rail
  • Measurement monitoring: sensor break
  • Adjustment limit value: no need to connect strain gauge

Digital measuring amplifier for strain gauge

Digital measuring amplifier for strain gauge

type: ADLM-LC | ID: LA

technical features

  • Input sensivity 01 to 5 mV/V
  • Programmable via RS232 interface
  • Analog output 4...20 mA and 0...10 V
  • Supply voltage 24 VDC +/- 30%
  • Combined error 0,2% FS
  • Resolution 12 / 14 / 15 / 16 bit
  • Enclosure stainless steel
  • Degree of protection IP 65

Summin amplifier for resistance strain gauge

Summing amplifier for resistance strain gauge

type: DSV | ID: DV

technical features

  • 4 inputs resistance strain gauge, full bridges
  • Addition of single measure values
  • 1 output for connection to every measuring amplifier with input for resistance strain gauge bridges
  • Cascading of several summing amplifiers is possible
  • External power supply for the bridges can be connected on demand

products "Made in Germany"

Müller Industrie-Elektronik manufactures measuring devices, sensors, transmitters, limit switches, calibrators and digital displays for industrial measuring and control technology, transmitters and amplifiers for signal processing, display devices and evaluation instruments in the region Hannover at the company location Neustadt am Rübenberge. Services such as contract manufacturing, board production, cable assembly, 3D construction, prototype construction and measuring device calibration complete the extensive product portfolio.