OEM Transmitter DMS HART

OEM Transmitter Strain Gauge HART

type: MASG-E | ID: ▒

technical features

  • Input: 1 strain gauge bridge, 4-wire
  • Bridge resistance: minimal 300 Ohm
  • Sensititivy: 1...4 mV/V
  • Output: 4...20 mA HART (2-wire)
  • Resolution: 16 bit
  • Strain gauge supply: 1 VDC
  • Gross error: 0,3% of range

OEM Tranmitter DMS HART

OEM Transmitter Strain Gauge HART

type: MASG-R | ID: ▒

technical features

  • Input: 1 strain gauge bridge, 4-wire
  • Bridge resistance: minimal 300 Ohm
  • Sensititivy: 1...4 mV/V
  • Output: 4...20 mA HART (2-wire)
  • Resolution: 16 bit
  • Strain gauge supply: 1 VDC
  • Gross error: 0,3% of range

OEM Transmitter Temperatur HART

OEM Transmitter Temperature HART

type: MART-E | ID: ▒

technical features

  • Input: multiple, see data sheet
  • Measurement rate: 100 measurements/s
  • Material PCB: FR4, PBT (electronics fully potted)
  • Output: 4...20 mA HART (2-wire)
  • Resolution: 16 bit
  • Switch-on delay: <5 s
  • Gross error: 0,3% of range

OEM Transmitter Temperatur HART

OEM Transmitter Temperature HART

type: MART-R | ID: ▒

technical features

  • Input: multiple, see data sheet
  • Measurement rate: 100 measurements/s
  • Material PCB: FR4, PBT (electronics fully potted)
  • Output: 4...20 mA HART (2-wire)
  • Resolution: 16 bit
  • Switch-on delay: <5 s
  • Gross error: 0,3% of range

Humidity sensor

Humidity sensor HART

type: MEHS | ID: FI

technical features

  • Input: 0...100% rHF
  • Output: 4...20 mA
  • Supply: 12...30 V
  • Fitting length: 72...300 mm
  • Temperature range: -40...+80 °C
  • Process connection: 1/2", 3/4", 1", 1,5", 1/2NPT
  • Electrical connection: several options
  • Protection: at least IP65

Modular compact differential pressure transmitter HART

Modular compact differential pressure transmitter HART

type: MKDS | ID: MP

technical features

  • Pressure: differential
  • Ranges from 75 mbar up to 70 bar
  • Output: 4...20 mA HART
  • Supply voltage: current loop, 12...30VDC
  • Accuracy: 0,1%, 0,075%, 0,2% of span
  • Degree of protection: IP65
  • Medium contact parts stainless steel 1.4435
  • Process connection 1/4-18NPT
  • Turn down up to 100:1

Pressure Transmitter Hygiene HART

Pressure Transmitter Hygiene HART

type: MEPS-H | ID: OQ

technical features

  • Input: 0…160 mbar up to 0...25 bar
  • Output: 4…20 mA current loop HART (2-wire)
  • Supply: from current loop 12...40 VDC
  • Accuracy: see Technical Data
  • Process connection: flange hygiene version
  • Electrical connection: multiple options
  • Ambient temperature: -20…+80 °C (operation)
  • Limit value contacts: 2x electronic (NPN, PNP)
  • Setting: keys / software
  • Medium temperature: -30…+100 °C
  • Protection class: at least IP65

Melt Pressure Sensor HART

Melt Pressure Sensor HART

type: MEMP-T | ID: AC

technical features


  • Input: 0...50 bar up to 0...1200 bar
  • Output: 4...20 mA HART, 2-wire / CANopen
  • Supply: by current loop 12...32 VDC
  • Accuracy: <0,5% of terminal value
  • Process connection: 1/2"-20UNF-2A with / without capillary tube
  • Electr. connection: MIL (standard), M12, cable outlet
  • Environmental temp.: -20...+85 °C
  • Medium temperature: -30...+410 °C
  • Setting: Software
  • Material: 1.4571 CrNi stainless steel
  • Protection class: at least IP65 / IP68

Magnetic Surface Temperature Sensor HART

Magnetic Surface Temperature Sensor HART

Typ: METS-WTM | ID: NW

technical features

  • Input: RTD Pt100 (maximum range -50...+200 °C)
  • Output: 4...20 mA current loop HART (2-wire)
  • Voltage supply: out of current loop (12...40 VDC)
  • Accuracy: see technical details
  • Process connection: clamping magnet
  • Electrical connection: several plugs
  • Temperature range: -20...+80 °C (ambient)
  • Limit value contacts: 2 electronically (NPN / PNP)
  • Adjustment: software
  • Material: stainless steel 1.4571 (medium contact)
  • Protection: at least IP65

Magnetic Surface Temperature Sensor HART

Magnetic Surface Temperature Sensor HART

Typ: METS-WSM | ID: NX

technical features

  • Input: RTD Pt100 (maximum range -50...+200 °C)
  • Output: 4...20 mA current loop HART (2-wire)
  • Voltage supply: out of current loop (12...40 VDC)
  • Accuracy: see technical details
  • Process connection: clamping magnet
  • Electrical connection: several plugs
  • Temperature range: -20...+80 °C (ambient)
  • Limit value contacts: 2 electronically (NPN / PNP)
  • Adjustment: keys / software
  • Material: stainless steel 1.5471 (medium contact)
  • Protection: at least IP65

Modular temperature sensor (HART) with spring

Modular temperature sensor with spring HART

type: MKTS-SP | ID: MK

technical features

  • Sensor: RTD Pt 100, Pt 1000, 2-, 3-, 4-wire
  • Protection: Inside completely potted
  • Material: Protecting tube and body stainless steel 1.4571
  • Process connection: 3/8", 1/2", 3/4"
  • Option: transmitter 4...20 mA HART
  • Settings: configurable with software
  • Connection: MIL, valve, M12x1, cable, Super Seal, Deutsch, Bayonet
  • Protection: at least IP 65

Ultrasonic Sensor (HART)

Ultrasonic Sensor HART

type: MEUS | ID: OX

technical features

  • Input: Ultrasonic echo
  • Ranges: 300...3500 mm, 200...2000 mm
  • Output: 4...20 mA (HART), 3-wire system
  • Supply: 24 VDC
  • Process connection: M30x1,5, M18x1
  • Electrical connection: M12x1, 8-pole
  • Temperature range: -15...+70 °C
  • Limit value contacts: 2 electronically (NPN/PNP)
  • Configuration: with keys/software
  • Material sensor tube: stainless steel, Option: synthetic

Intrinsically safe level sensor HART | GL- and Ex-approval

Intrinsically safe level sensor HART | GL- and Ex-approval

Typ: PT-HL | ID: UH

technical features

  • Ranges: 0...0,1 bar up to 0...10 bar
  • Output: 4...20 mA HART
  • Voltage supply: Current loop, 16...30VDC
  • Accuracy: 0,5% (0,25%)of span
  • Protection: IP68
  • Material enclosure: CrNi-Stahl, Hastelloy
  • Temperature range: -10...+85 °C
  • Connection: Cable

Strain gauge amplifier HART

Strain gauge amplifier HART

type: DRMU-S2 - DRSG-S2  | ID: DR series 2

technical features

  • Input: 1 strain gauge full bridge
  • Bridge resistance: 350 Ω minimum
  • Output: 4...20 mA HART current loop
  • Supply: Current loop
  • Electrical connection: 2...6 plug-in terminal strip
  • Limit vale contacts: without
  • Protection: IP20
  • Accuracy: see data sheet
  • Enclosure: for DIN rail

Strain gauge amplifier HART

Strain gauge amplifier HART

type: DRMU-S4 - DRSG-S4 | ID: DR series 4

technical features

  • Input: 1 strain gauge full bridge
  • Bridge resistance: 350 ohms minimun
  • Output: 4...20 mA HART current loop
  • Supply: 24 VDC, 85...250 VAC, current loop
  • Electrical connection: 2...6 plug-in terminal strip
  • Limit vale contacts: 2x electronically,
    2x relays
  • Protection: IP20
  • Accuracy: see data sheet
  • Enclosure: for DIN rail

ME - Gas Cylinder Scale

ME - Gas Cylinder Scale

Typ: ME-GFW1 | ID: CZ

Technische Features

  • Messbereich ME-GFW1: 250 kg
  • Ausgang: 4...20 mA HART Stromschleife
  • Grenzwertkontakte: 2x elektronisch PNP
  • Versorgung: 12...40 VDC (aus Stromschleife)
  • Elektrischer Anschluss: 2x M12x1, 5-polig
  • Temperaturbereich: -20...+55 °C
  • Überlastungsschutz: einstellbar über 3 Klemmringe
  • Schutzart: IP65
  • Einstellung: Tasten / Software

ME - Gas Cylinder Scale

ME - Gas Cylinder Scale

Typ: ME-GFW2 | ID: CZ

Technische Features

  • Messbereich ME-GFW2: 500 kg
  • Ausgang: 4...20 mA HART Stromschleife
  • Grenzwertkontakte: 2x elektronisch PNP
  • Versorgung: 12...40 VDC (aus Stromschleife)
  • Elektrischer Anschluss: 2x M12x1, 5-polig
  • Temperaturbereich: -20...+55 °C
  • Überlastungsschutz: einstellbar über 3 Klemmringe
  • Schutzart: IP65
  • Einstellung: Tasten / Software

Screw-in thermocouple temperature sensor

Screw-in thermocouple temperature sensor HART

Typ: METS-TS | ID: OS

technical features

  • Measuring element: thermocouple type K
  • Potting: electronics completely potted
  • Material: process connection stainless steel 1.4571
  • Process connection: 1/4", 3/8", 1/2", 3/4", 1", 1/4" NPT, 3/8" NPT, 1/2" NPT
  • Output: 4...20 mA HART
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Screw-in resistance temperature sensor

Screw-in resistance temperature sensor HART

Typ: METS-WS | ID: OR

technical features

  • Measuring element: RTD Pt 100
  • Potting: electronics completely potted
  • Material: process connection stainless steel 1.4571
  • Process connection: 1/4", 3/8", 1/2", 3/4", 1", 1/4" NPT, 3/8" NPT, 1/2" NPT
  • Output: 4...20 mA HART
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Screw-in resistance temperature sensor

Screw-in resistance temperature sensor HART

Typ: METS-WT | ID: OH

technical features

  • Measuring element: RTD Pt 100
  • Potting: electronics completely potted
  • Material: process connection stainless steel 1.4571
  • Process connection: 1/4", 3/8", 1/2", 3/4", 1", 1/4" NPT, 3/8" NPT, 1/2" NPT
  • Output: 4...20 mA HART
  • Electrical connection: lateral, upwards
  • Configuration: software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Modular compact temperature sensor HART

Modular compact temperature sensor HART

type: MKTS| ID: MK

technical features

  • Measuring element as Pt 100, Pt 1000, 2-, 3-, 4-wire
  • Inside of case completely potted
  • Protection tube and case are made of stainless steel 1.4571
  • Process terminal thread 1/4", 3/8", 1/2", 3/4", 1/4" NPT, 3/8" NPT, 1/2" NPT
  • optional transmitter 4...20 mA, programmable
  • Cable connection with plug MIL D38999, valve plug DIN EN 175301-803,
  • RSE4 compatible plug M12x1, cable entry M12x1,5 with cable
  • Degree of protection IP 67

Pressure sensor

Pressure sensor HART

type: MEPS-T | ID: OD

technical features

  • Pressure: relative, absolute
  • Ranges 0...0,1 bar up to 0...1000 bar
  • Potting: electronics completely potted
  • Material: in contact with medium stainless steel 1.4571
  • Process connection: 1/2" / 1/4" / 1/2NPT / 1/4NPT
  • Output: 4...20 mA HART
  • Configuration: software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Differential pressure sensor HART

Differential pressure sensor HART

type: MIDS | ID: MD

technical features

  • Ranges 0…10 mbar, 0…40 mbar or 0…100 mbar
  • Potting: electronics potted
  • Process connection: 2x hose connection 4 mm
  • Output: 4...20 mA HART
  • Configuration: factory configuration via software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Pressure sensor standard

Pressure sensor standard HART

type: MEPS-S | ID: OP

technical features

  • Pressure: relative, absolute
  • Ranges 0...0,1 bar up to 0...1000 bar
  • Potting: electronics completely potted
  • Material: in contact with medium stainless steel 1.4571
  • Process connection: 1/2" / 1/4" / 1/2NPT / 1/4NPT
  • Output: 4...20 mA HART
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Modular pressure transmitter

Modular pressure transmitter HART

type: MHPS | ID: HP

technical features

  • Pressure: relative, absolute
  • Ranges 0...0,1 bar up to 0...1000 bar
  • Output: 4...20 mA HART
  • Supply voltage: current loop, 15...30VDC
  • Accuracy: 0,25% (0,5%) of span
  • Degree of protection: IP65
  • Medium contact parts: CrNi steel
  • Process connection: 1/2" / 1/4" / 1/2NPT / 1/4NPT / M20x1,5
  • Display with programming keys
  • Turn down up to 100:1

Modular differential pressure transmitter

Modular differential pressure transmitter HART

type: MHDS | ID: HD

technical features

  • Pressure: differential
  • Ranges from 10 mbar … 100 bar
  • Output: 4...20 mA HART
  • Supply voltage: current loop, 15...30VDC
  • Accuracy: 0,1%, 0,075%, 0,2% of span
  • Degree of protection: IP65
  • Medium contact parts stainless steel 1.4435
  • Process connection 1/4-18NPT
  • Display with programming keys
  • Turn down up to 100:1

Level sensor with float

Level sensor with float HART

type: MELS-F | ID: OL

technical features

  • Measuring element: float
  • Potting: electronics completely potted
  • Material: in contact with medium stainless steel 1.4571
  • Process connection: 1", 1,5", 1"NPT
  • Output: 4...20 mA HART
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Modular and compact level sensor/switch HART

Modular and compact level sensor/switch HART

type: MKLS | ID: MN

technical features

  • Input: conductivity
  • Level: 100...2000 mm
  • Medium: non aggressive fluids
  • Option: with RTD Pt100, 2-wire
  • Process connection: several options
  • Electrical connection: several options
  • Material: stainless steel 1.4571
  • Output: 4...20 mA / contacts
  • Degree of protection: IP65 (electronics) /
    IP 68

Modular temperature transmitter

Modular temperature transmitter

type: MHTT | ID: HM

technical features

  • Input: RTD / TC / voltage (mV)/ resistance (potentiometer)
  • Output: 4...20 mA current loop, HART protocol
  • Supply: 15...45 VDC out of current loop
  • Accuracy: 0,08...0,12% of range
  • Indication: LCD display (backlighting)
  • Galvanical insulation: input / output
  • Settings: with software via HART-protocol
  • Enclosure: diecast aluminium

ME-OEM-Transmitter

ME-OEM-Transmitter HART

Type: ME-OEM | ID: OE

technical features

  • Input: RTD Pt100, strain gauge, mV, mA, V, R, potentiometer, PWM,
  • Input: TC type K, J, E, T, R, S, B / piezo
  • Potting: electronics potted
  • Process connection: customized, M12x1 female thread
  • Output: 4...20 mA HART
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Electr. connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65

Electronical limit value contacts for MH-Series

Electronical limit value contacts for MH-Series

type: MH-LVE

technical features

  • Input: 4...20 mA HART (current loop)
  • Supply: out of current loop
  • Limit contacts: 2 open collectors (36 VDC, 150 mA)
  • Connection: plug-in terminal strip
  • Accuracy: 0,2% of range, 1 digit
  • Protection: IP20 (PCB)
  • Mounting: plugable with fastening screws
  • Settings: with 3 keys

Digital measuring amplifier for strain gauge HART

Digital measuring amplifier for strain gauge HART

type: ADHM-LC | ID: LH

technical features

  • Connection: 1x strain gauge full bridge, 350 ohms
  • Input sensitivity: 1...4 mV/V
  • Configuration: via HART interface
  • Output: 4...20 mA HART
  • Supply: 12...40 VDC out of current loop
  • Electrical connection: pluggable - Combined error: 0,3% of nominal range
  • Resolution: 16 bit
  • Enclosure: stainless steel
  • Protection: IP 65

Modulare Universal - Kraftmesszelle

Modular Universal - Load Cell Standard HART

Type: MULC-S | ID: CH

Technische Features

  • Sensor input: load suspension device
  • Function load cell: tension load, compression load,
  • tension and compression load
  • Measuring range: 1000 kg, 1500 kg, 3000 kg
  • Output: strain gauge / 4...20 mA HART
  • Supply: 12...40 VDC current loop / bridge supply 10 VDC
  • Accuracy: see technical data
  • Protection: IP54
  • Vibration protection: electronics completely potted
  • Configuration: via superimposed HART communication
  • Material load cell: stainless steel, alloy steel nickel-plated
  • Accessories: rod end

Transmitter Resistance Thermometer HART

Transmitter Resistance Thermometer HART

type: TH-RTD | ID: ▒

technical features

  • Input RTD: Pt100, Pt1000
  • Output: 4...20 mA current loop
  • Supply: 12...40 VDC out of current loop
  • Accuracy: 0,3% of nominal range
  • Configuration: HART-interface
  • Connection: Terminal screws
  • Protection: IP20
  • Dimensions: d=45x23 mm
  • Enclosure: Synthetics black

Differential pressure sensor HART

Relative Pressure Transmitter HART

type: MIPS | ID: MO

technical features

  • Input: pressure 0...10 mbar up to 0...1 bar
  • Output: 4...20 mA current loop HART (2-wire)
  • Voltage supply: out of current loop (12...40 VDC)
  • Accuracy: see technical details
  • Process connection: 1x hose connection
  • Medium: clean dry air, dry gases
  • Electrical connection: several plugs / cable
  • Temperature range: -20...+80 °C (operation)
  • Adjustment: software
  • Material enclosure: PBT GF 30
  • Protection: at least IP65

Pressure Sensor - Flush HART

Pressure Sensor - Flush HART

type: MEPS-F | ID: OZ

technical features

  • Input: 0...0,1 to 0...600 bar / 0...0,25 to 0...16 bar
  • Output: 4...20 mA current loop HART (2-wire)
  • Supply: out of current loop (12...40 VDC)
  • Accuracy: see technical data
  • Process connection: G1/2B / G1B flush-mounted / G1 hygienic
  • Electrical connection: several options (page 3)
  • Ambient temperature: -20...+80 °C (operation)
  • Limit value contacts: 2x electronic (NPN, PNP)
  • Setting: Keys / Software
  • Medium temperature: -30...+100 °C
  • Protection: at least IP65

Temperature limit value switch HART

Temperature limit value switch HART

type: TGS2 | ID: TG

technical features

  • Input RTD Pt100: 2-wire / -50...500 °C
  • Thermocouple type K: NiCr-Ni / -50..1..200 °C
  • Output: Relay contact (NC or NO)
  • Supply: 24 VDC
  • Accuracy: 0,3% of nominal range
  • Operation temperature: -20...+80 °C
  • Configuration: HART interface, magnet
  • Connection: Terminal screws
  • Protection: IP20
  • Dimensions: Ø45x23 mm
  • Enclosure: Synthetics PA66

room temperature sensor HART

Room temperature sensor HART

Type: MITS | ID: MR

technical features

  • Sensor: RTD Pt100, Pt1000, 2-, 3-, 4-wire
  • Enclosure: inside completely potted
  • Protecting tube: stainless steel 1.4571
  • Range: -30...+60 °C
  • Option: transmitter 4...20 mA HART
  • Connection: MIL plug, valve plug, M12x1, cable
  • Protection: at least IP65

Hand-held temperature sensor

Hand-held temperature sensor HART

Type: MKTS-HA | ID: MH

Technische Features

  • Measuring element: RTD Pt 100(0), 2-, 3-, 4-wire
  • Accuracy: Class A, B, B 1/2 DIN
  • Output: RTD Pt100(0), 4...20 mA HART, interface
  • Enclosure inside completely potted
  • Protecting tube and handle made of stainless steel 1.4571
  • Process connection: tip of tube flat, pointed
  • Length of tube: 50...1000 mm
  • Connection: several plugs, cable
  • Protection: IP65

Strain gauge amplifier HART

Strain gauge amplifier HART

type: MISG | ID: MJ

technical features

  • Input strain gauge: 1 full bridge, 4-wire
  • Input sensitivity: 1...4 mV/V
  • Output: 4...20 mA HART
  • Voltage supply: 12...40 VDC
  • Resolution: 16 bit
  • Combined error: 0,3% of range
  • Bridge supply: 1 VDC
  • Protection: at least IP65
  • Configuration: Software with HART communication

Screw-in infrared temperature sensor

Screw-in infrared temperature sensor HART

Typ: METS-IR | ID: OC

technical features

  • Measuring element: Infrared radiation
  • Maximum range: -40...+ 1000 °C
  • Output: 4...20 mA HART
  • Process connection: 1/2", 3/4", 1", 1/2" NPT
  • Voltage supply: 24 VDC +/- 10 %
  • Limit value contacts: 2 electronically
  • Configuration: with keys/software
  • Connection: M12 male, 8-pole
  • Protection: at least degree IP65

Level sensor with float

Level sensor with float HART

type: MELS-FT | ID: OV

technical features

  • Measuring element: float
  • Potting: electronics completely potted
  • Material: in contact with medium stainless steel 1.4571
  • Process connection: 1", 1,5", 1"NPT
  • Output: 4...20 mA HART
  • Configuration: software
  • Electrical connection: lateral, upwards
  • Connection: M12, Super Seal, Deutsch, Bayonet, valve, cable
  • Protection: at least degree IP65